In order to piece quilt batting, at first, overlap the uneven edges of the battings and make them even by making use of a rotary cutter. Lay the battings side by side without overlapping on a hard surface and sew the butts together by either machine stitching or loosely hand stitching them.
How to Piece Quilt Batting?
As a quilter, you most probably do not like throwing away the scrapped quilt batting because they are expensive. You can actually make use of the long pieces, sew them together to make a very large piece, and make it easier for you to work with.
Step 1: Overlap the Edges of the Batting
At first, gather two large pieces of batting and lay them flat on a table beside each other. If you already have two straight seams, it’s very simple. You can join them pretty easily.
However, that’s not the case usually for scrapped quilt batting. It’s usually a zigzag, uneven, or all cut up. Therefore, you must devise a way to join those two odd sizes together.
The first thing you do is to make sure your batting is nice and flat on your surface. Then you will overlap them slightly, joining up one edge. Hover your palm over them to make sure it’s nice and flat. Batting is bulky and you do not want any extra bump or bulk in the areas of sewing.
Step 2: Cut Between the Layers Using a Rotary Cutter
The next thing, you will just cut between those layers. You don’t need a ruler to make sure the overlapping is straight. As long as you’re fairly straight, it’s going to be fine.
Just cut through both the layers using a rotary cutter and you will be able to remove the top and bottom pieces all the way along. That’s how you can have two seams that actually match.
Step 3: Sew the Butts Together
Next, keep the edges together but do not overlap them. You can hand sew them with a needle or you can bring them to the sewing machine. Doing this process by machine stitching is much easier and more accurate.
First of all, you have to set up the machine. The batting is a bit thicker than the fabric and you do not want the feed dogs to work against you. Therefore, make the presser foot as loose as you can from the surface and adjust the pressure on the foot.
The foot must be such that you can do a zigzag on. The zigzag should be as wide as possible and the stitch length should be as large as possible. In other words, make sure the zigzag is the largest with the less presser foot.
Sew It up to the End
Now place the edges of the battings together and sew all the way down. Instead of overlapping, you are just going to butt the edges together. Put your foot and needle down and start sewing. Keep your seams together and do not pull or push the fabric. The sewing machine will do the rest.
Following the same procedure, you can stitch together multiple pieces of quilt batting. If any piece of the entire batting is not lying flat, you can just cut that part out and make it lie flat.
Then use the rotary cutter to make the seams even and remove the pieces the same way as before. Lastly, sew the even seams together using a sewing machine.
How to Join Batting by Hand?
Once you are done with the task of making the batting edges even, one of the options of joining them together is by hand stitching. Going on with this method, you do not need to be super-secure. You are only going to loosely join them together until the actual quilting gets done. Your quilting is what will hold them together later.
You should choose a matching thread to sew the batting pieces together. Now, place the batting pieces on a hard surface and make sure there are no bumps. At the beginning and end of the seam, give it a secure “tacking” stitch.
Then start making big stitches down the seam while keeping the stitches fairly loose. Do not pull the stitches so hard that the batting puckers up. If you feel that it is secure enough, then leave it like this. However, joining multiple batting pieces by hand stitching can be pretty backbreaking.
How to Store Quilt Batting?
To store the quilt batting, you can make use of the original packaging from your batting. This gives you an opportunity to store your leftover batting in the same bag. As a result, you get information such as the type of batting that is in there and how you are going to use it.
All you need to do is to cross out the original size that would be posted on the bag and put the size that you have as leftover. Therefore, just measure it first and put the size on the bag.
You can keep bigger bags of the batting and put more than one in them. Cross off the sizes and put the new size in there. That way you can reuse the same bag.
Frequently Asked Questions
Can I piece together batting for a quilt?
You can piece together batting for a quilt if the batting pieces are large enough. By hand stitching or machine stitching, you can piece multiple battings together and make it large enough for a quilt.
Can I iron my quilt batting?
You can iron the quilt batting as long as there is no polyester content at all. However, many types of cotton and other natural fiber battings contain polyester. If you hot iron them, the battings are most likely to melt.
Quilt battings are expensive and it is not for a quilter to just throw them away. The longer pieces can be reused to make another quilt and the smaller pieces can be used for stuffing. These fabrics need extra care when you piece your quilt batting together and you do not want to mess them up.